兰鹏，男，2015年1月博士毕业于北京科技大学钢铁冶金系，获得北京科技大学第十届研究生十佳学术之星，随后留校做师资博士后。2015年7月至2016年7月于浦项工科大學开展博后工作，2017年6月聘为北京科技大学钢铁冶金系讲师。已发表论文30余篇，其中第一作者的SCI/EI检索论文近20篇，是Metallurgical and Materials Transaction A、Journal of Alloy and Compounds, Materials Characterization, Steel Research International等国际期刊的通讯审稿人。
代表性论著：
1. Lan P, Nguyen D A, Lee S Y, et al. Heat transfer and solidification microstructure evolution of continuously cast steel by non-steady physical simulation[J]. Metals and Materials International, 2017, 23(3): 568.
2. Lan P, Zhang J. Twinning and Dynamic Strain Aging Behavior during Tensile Deformation of Fe-Mn-C TWIP Steel[J]. Materials Science and Engineering: A, 2017.
3. Lan P, Tang H, Zhang J. Hot ductility of high alloy Fe–Mn–C austenite TWIP steel[J]. Materials Science and Engineering: A, 2016, 660: 127.
4. Lan P, Tang H, Zhang J. Solidification Microstructure, Segregation, and Shrinkage of Fe-Mn-C Twinning-Induced Plasticity Steel by Simulation and Experiment[J]. Metallurgical and Materials Transactions A, 2016, 47(6): 2964.
5. Lan P, Zhang J. Thermophysical properties and solidification defects of Fe–22Mn–0.7 C TWIP steel[J]. steel research international, 2016, 87(2): 250.
6. Lan P, Zhang J. Study on the mechanical behaviors of grey iron mould by simulation and experiment[J]. Materials & Design, 2014, 53: 822.
7. Lan P, Zhang J. Strength, microstructure and chemistry of ingot mould grey iron after different cycles of low frequency high temperature loads[J]. Materials & Design, 2014, 54: 112.
8. Lan P, Zhang J. Analysis of Solidification Microstructure and Hot Ductility of Fe-Mn-C TWIP Steel[J]. Mater Sci Technol, 2014, 30(11):1297.
9. Lan P, Zhang J. Numerical Analysis of Macrosegregation and Shrinkage Porosity in Large Ingot[J]. Ironmak Steelmak, 2014, 41(8):598.
10. Lan P, Zhang J. Effect of Mould taper and Wall Thickness on Steel Ingots Soundness by 3-D Solidification Simulation[C]. The Minerals,Metals & Materials Society 2012.
11. 兰鹏, 唐海燕, 纪元, 等. Fe-22Mn-0.7C TWIP 钢的热塑性与断裂机制[J]. 工程科学学报, 2016, 38(6): 795.
12. 兰鹏, 杜辰伟, 陈培莉, 等. 微合金钢连铸表面横裂纹形成机理与控制技术研究现状[J]. 钢铁研究学报, 2017, 29(1): 1.
13. 兰鹏，张家泉. 430不锈钢凝固显微组织模拟的3D CAFE模型[J]. 北京科技大学学报，2014, 36(3): 315.
14. 兰鹏，张家泉. 微观组织参数及工艺条件对430不锈钢凝固显微结构的影响[J]. 北京科技大学学报，2014, 36(4): 446.
15. 兰鹏，张家泉. 钢锭模用灰口铸铁服役工况下组织与力学行为研究[J]. 机械工程学报, 2014, 50(2):116.
16. 兰鹏，张家泉. 灰口铸铁低频热疲劳载荷下的微观组织与拉伸性能[J]. 材料热处理学报, 2014, 34(4):149.
